Customers Viewing This Page May Be Interested in These Items:

DIAMOND DERMABRASION

Diamond Dermabrasion provided a non-surgical skin refinish procedure, by using sterile diamond heads to abrade or rub off the top skin layer, then vacuuming out the particles along with any dirt and dead skin back up. This procedure removes skin debris, imperfections, blemishes, wrinkles and unwanted pigmentation on the skin. Moderate usage of Diamond Dermabrasion, accompany with skin products that penetrate through top skin layer that reach the dermis level, helps to replenish natural nutrients, restore cell activity, and promote skin health.
The results after Micro Dermabrasion
treatment is usually a healthy, glowing, beautiful skin. Diamond Microdermabrasion is generally indicated for:
*Rejuvenation of sun damaged skin - face, neck, shoulders, back, arms and legs
*Reduction of age spots.
*Minimization of blotchy skin coloring.
*Reduction of acne and superficial scars from past injury.
*Extraction of blackheads and whiteheads.
*Reduction of oily Skin.
*Improvement of overall skin health.


Note:
Two stainless steel wands which are used with 9 interchangeable diamond tips(D80,D100,D120,D150,D180,D220,D160,D180,Smooth Tip)
1- The higher the D number,the finer the grit
2- Clean diamond tips with Alcohol,then sterilize them with UV light or high temperature
3-Replace the big cotton filter inside the vacuum connector after every five to six treatment
4- Replace the small cotton filter on the wand head after every treatment

SKIN SCRUBBER

Scrubber function removes dead skin cells,smooth wrinkles,treats pimples and clears the complexion.It uses ultrasonic waves to shake loose dead skin cells,it also create heat and vibration to give a pleasant massage which will drive creams and ampouls into the skin

Operation instructionbber
Caution:
1.Please don\'t turn on usage with long time,better use scrubber within 15-30 minutes per time.Then stop the scrubber for 20mintes before the next scrubber operation.Long time operation will burn the scrubber grey box and destroy the control board of the whole machine
2 If salon treatment schedule is full everyday,please prepare two or more machines for alternate use.Don\'t use one machine for serveral customers and never stop,this will reduce the service life of machine

Cleasing skin
1 Apply cleanser to skin,Massage well and remove using the skin scrubber with curved side pointing up,at a 45 degree angle(removing product,with a slight scraping motion)Wipe an y excess product on a tissue or a cotton 4x4 pad.Skin scrubber should be on continuous current for this process
2 Finish removing cleanser with sponges,cotton rounds,or hot/warm to wel

Skin care
1 After the skin is properly cleansed,apply a serum,cream,gel or ampoule appropriate for the skin type and skin condition of your client
2 Using the small flat side of the skin scrubber,move aroud the skin to penetrate product,the skin scrubber should be set to the pulsating current

ULTRASONIC

Ultrasonic utilizes sonic vibrations; it works one million times per second. The ultrasonic wave could stimulate skin tissue and improve permeability of the membrane to promoted collagen tissue, reduced wrinkle and invisible appeared fine line, also lift the skin result for younger and healthy look. Ultrasonic generate frictional heat which accelerate blood circulation, muscle relaxation, and decompose the cellulite to bread down exceed fat. NV-07 Ultrasound with 2 probes provided non-surgical lifting. This machine utilizes sonic vibrations to reduce lines, leaving the skin firm and smooth.

Preparation before treatment
1 Before beginning Ultrasound make sure the skin in cleansed,and then apply an appropriate gel,serum,or cream for the appropriate skin type or condition.Make sure the product has some slip to it
2 Choose the pointed or flat head.Use pointed head for around the eyes,and the flat head for the face and neck

THE HOT & COLD TREATMENT

The cold treatment function is specially designed for calming down the skin after peeling. The skin is sensitive after peeling treatment, so the cold treatment procures is necessary. The hot treatment function is designed for opening pores before cleaning the skin and accelerating the absorption of nutrition.

Note:
1 -wait 2-3 minutes for the hammer to get cold or hot before starting treatment
2-The treatment should be approximately 5-10 minutes,Do not stay in one area of the skin too long this will avoid any damage to skin from the hot/cold head
3- Clean head before and after every treatment,wiping with alcohol or disinfectant wipe